How to check and adjust the operating clearance of slurry pump?

A guide to starting, running, maintaining and disassembling a mortar pump:

1. Start-up and operation

1.1 Pre-run inspection: Before test run, rotate the coupling or shaft by hand to make sure the direction is correct and the operation is flexible. If there is any abnormality, it is necessary to check the coupling level and lubricant level, and keep it near the centerline of the oil mirror. If the problem persists, refer to the instruction manual to disassemble the pump to clean the foreign matter, if necessary, contact the manufacturer to seek a solution.

1.2 Starting steps: First fill the pump with liquid, open the inlet valve (check valve without manual), turn on the power, and finally open the outlet valve.

1.3 Operation monitoring: If there is any abnormal sound or motor heating, stop the pump immediately for inspection, refer to 1.1 for the method.

1.4 Stopping operation: Close the outlet valve first, disconnect the power supply, and close the inlet valve at the same time (the check valve does not need to be manually).

1.5 Maintenance: The lubricant should be changed every six months. After stopping the pump in winter, thaw the sealing place, and then start the pump according to the starting procedure.

2. Disassembly and installation procedures

2.1 Pumps without impeller: From loosening the connecting bolts to removing the sealing box and checking the clearance during installation, make sure that the clearance between the impeller and the pump body is about 2mm.

2.2 Pumps with paid impellers: When disassembling, first remove the paid impeller and other parts, and when installing, check the clearance as well, and adjust the shims as necessary to ensure that the clearance is appropriate.

Comments

What are the differences bewteen core drilling bits and pdc drilling bits

Although both core drills and PDC drills are tools used for drilling and sampling, there are significant differences between them in terms of material, structure, and scope of application. Core Drill Definition: A core drill is a broad concept that refers to all drills used for coring operations. It can be a variety of types such as tungsten carbide bits, PDC bits, diamond bits and so on. Function: Mainly used to remove a cylindrical section of core sample from different types of materials for subsequent analysis and research. Material: Various materials, including carbide, diamond, PDC, etc. Different materials are selected according to the hardness and toughness of the drilling material. Structure: Relatively simple structure, mainly consists of drill body, inner cylinder and outer cylinder. Application: Wide range of applications, including geological exploration, engineering survey, mineral exploration, etc. PDC Drill Bit Definition: PDC drill bit is a special coring dr...

Does the water well drilling bit have a warranty

Whether or not a water well drill bit has a warranty, and the length of that warranty, depends on several factors: Drill Bit Type: Different types of drill bits vary greatly in their structure, material and manufacturing process, and therefore warranty policies will vary. For example, PDC bits (polycrystalline diamond composite bits) usually have a longer warranty due to their higher technology, whereas some simple tooth wheel bits or diamond bits may not have a defined warranty or may have a shorter warranty. Manufacturer/Supplier: After-sales service policies and reputations vary between manufacturers or suppliers. Some large, reputable manufacturers usually offer a good warranty, while some small, unknown suppliers may not offer a warranty or may have harsh warranty terms. Purchase Contracts/Agreements: When purchasing a drill bit, it is important to read the terms of the purchase contract or agreement carefully, especially the sections on warranty and after-...

How to replace the impeller of a slurry pump

The impeller of the slurry pump is a wearing part, which needs to be inspected and replaced periodically. The process of replacing the impeller is relatively complex and requires certain specialized knowledge and skills. The following are the steps for replacing the impeller of the slurry pump: 1. Preparation Shut down and disconnect the power: Before any operation, be sure to cut off the power supply to ensure safety. Preparation tools: ready wrenches, screwdrivers, gaskets, new impeller and so on. Drain: Empty the pump. Protective measures: Wear protective gloves, safety glasses and other protective equipment. 2. Disassembly Procedure DISASSEMBLY: Disassemble the suction and discharge pipes connected to the pump. Remove pump cover: Loosen the bolts securing the pump cover and carefully remove the cover. Remove the impeller: Loosen the nuts secure the impeller with a suitable tool and remove the impeller. 3. Install the new impeller Insp...

Pearldrill PDC Bits and Pumps

Search This Blog